Our Brands

WOOD

  • Paslode
  • GRK Fasteners

CONCRETE

  • RedHead
  • Ramset
  • TapCon

STEEL & SPECIALTY

  • Buildex

T4MAG

Ramset’s T4MAG is the best-balanced tool available and is easy to use overhead. With 30% more power to
work in the toughest concrete, this tool will drive your job site productivity and result in lower user fatigue
and downtime.

Quick info

SKU: T4MAG Category:

THE PREMIER FASTENING SYSTEM FOR COMMERCIAL DRYWALL CONTRACTORS

ADVANTAGES

  • Higher stick rate than industry standard
  • 30% more power to work in the toughest concrete
  • Drives pins flush to create full embedment
  • Lower pushdown force and shorter travel distance decrease user fatigue
  • Reduced jamming, resulting in less downtime on the job
  • Superb balance leads to optimal user experience

T4MAG Increase Your Range with Overhead Power

The Power of the T4MAG allows you to consistently shoot where no other gas tool has gone before. The .125 diameter pin is specifically engineered to work in the toughest concrete and steel where other pins cannot perform. The new T4MAG system delivers power that rivals other gas and powder systems.

NEW: Convert your T4MAG tool into a SINGLE SHOT Tool with the NEWEST T4SS CONVERSION KIT

Click here for full product selection and performance tables for the T4MAG; Click here for full catalog pages for the T4MAG.

PERFORMANCE TABLES

GAS FASTENERS IN STEEL

PART NUMBER
SHANK DIA.
(INCH)
TYPE OF
SHANK
INSTALLED IN A36 STRUCTURAL STEEL – STEEL THICKNESS INCHES
ALLOWABLE LOAD –
Ultimate Load
3/16 (.1875)
1/4 (.250)
3/8 (.375)
TENSION (LBS)
SHEAR (LBS)
TENSION (LBS)
SHEAR (LBS)
TENSION (LBS)
SHEAR (LBS)
T3012S
0.125
TAPER SMOOTH
----- | -----
----- | -----
237 | 1184
356 | 1782
189 | 943
392 | 1960

Note 1:  ALLOWABLE loads are shown in the LARGE BOLD font, Ultimate loads are shown in smaller italic font.  Note 2:  Testing conducted in accordance with ICC AC70 & ASTM E1190.  Note 3:  Safety factors are based on coefficient of variation. In accordance with ICC AC70, the safety factor will be no less than 5.  Note 4:  Cyclic, fatigue, shock loads and other design criteria may require a different safety factor.  Note 5:  Job site testing may be required to determine actual job site values.  Note 6:  Values shown are for fastenings that have the entire pointed end of the fastener driven through the steel plate; except as noted below.  Note 7:  Fastener penetration is .31″ minimum.  Note 8:  Fastener penetration is .29″ minimum.  Note 9:  Fastener penetration is .27″ minimum.  Note 10:  Fastener penetration is .25″ minimum. Note 11: For SI: 1 lbf = 4.448 N, 1 inch = 25.4 mm, 1 ksi = 6.89MPa

COLLATED GAS FASTENERS IN CONCRETE

PART
NUMBER
SERIES
SHANK
DIAMETER
(INCH)
MINIMUM
PENETRATION
(INCH)
INSTALLED IN STONE AGGREGATE CONCRETE – CONCRETE COMPRESSIVE STRENGTH ALLOWABLE LOAD – Ultimate Load
2000 PSI
3000 PSI
4000 PSI
TENSION (LBS)
SHEAR (LBS)
TENSION (LBS)
SHEAR (LBS)
TENSION (LBS)
SHEAR (LBS)
T3
Straight Shank
0.125
5/8
83 | 414
109 | 611
----- | -----
----- | -----
78 | 426
80 | 574
3/4
107 | 541
156 | 855
----- | -----
----- | -----
104 | 593
195 | 977
PART
NUMBER
SERIES
SHANK
DIAMETER
(INCH)
MINIMUM
PENETRATION
(INCH)
INSTALLED IN STONE AGGREGATE CONCRETE – CONCRETE COMPRESSIVE STRENGTH ALLOWABLE LOAD – Ultimate Load
3000 PSI
LIGHT WEIGHT CONCRETE
3000 PSI
LIGHT WEIGHT CONCRETE
WITH METAL DECK
HOLLOW CONCRETE MASONRY
UNITS (CMU) ANY LOCATION
TENSION (LBS)
SHEAR (LBS)
TENSION (LBS)
SHEAR (LBS)
TENSION (LBS)
SHEAR (LBS)
T3
Straight Shank
0.125
5/8
84 | 418
108 | 540
72 | 361
242 | 1210
20 | 243
34 | 264
3/4
108 | 540
173 | 864
93 | 470
288 | 1442
----- | -----
----- | -----

Note 1:  ALLOWABLE loads are shown in the LARGE BOLD font, Ultimate loads are shown in smaller italic font.  Note 2:  Testing conducted in accordance with ICC AC70 & ASTM E1190.  Note 3:  Safety factors are based on coefficient of variation. In accordance with ICC AC70, the safety factor will be no less than 5.  Note 4:  Values shown in concrete are for the fastener only. Connected members must be investigated separately.  Note 5:  Cyclic, fatigue, shock loads, and other design criteria may require a different safety factor.  Note 6:  Job site testing may be required to determine actual job site values.  Note 7:  Minimum edge distance in concrete is 3 inches unless otherwise approved.  Note 8:  For SI: 1 lbf = 4.448 N, 1 inch = 25.4 mm, 1 ksi = 6.89MPa.  Note 9:  T3 straight shank allowable tension value in face shell of hollow CMU is 133 lbs.

APPROVALS / LISTINGS

ICC ESR 1955 – Fasteners

COLA RR-22668 – Fasteners

AUTHORIZED RAMSET SERVICE CENTRES

Click here for List of Authorized Ramset Service Centres


 

  • Part #T4MAG
  • Length17"
  • Height16-1/4"
  • Weight8.55 lbs.
  • Pin Guide O.D.590
  • Fuel Cell1000 shots
  • Battery (Charged)3500 shots
  • Magazine Capacity45 pins
  • Maximum Pin Length1
  • Ramset warrants that new T3MAG systems power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below.

    TWO-YEAR/50,000 SHOT WARRANTY
    A two-year/50,000 shot warranty, which ever comes first, will apply to all parts,
    except those listed below as normal wearing parts, or parts which are specifically covered by an extended warranty.

    SIX-MONTH/10,000 SHOT WARRANTY
    A six-month/10,000 shot warranty applies to the following parts, which are considered normal wearing parts:
    • Bumper
    • Piston Assembly
    • Metal Seal Rings
    • Piston Rings

    The warranty period is based off of tool build date, determined from the tool serial number. Ramset may extend the warranty time frame from the date of purchase with a qualifying document proving date of purchase.

    For full warranty statement, click here.

Part No. T4FUEL
Fuel Cell–T4
Qty: 12 (4–3 packs)

Part No. 018151
Battery–T4
Qty: 1

Part No. 018152
Battery Charger–T4
Qty: 1

 

T4MAG Fuel/Pin Pack
510 PINS AND 1 FUEL CELL PER BOX.
PART NUMBER
SHANK LENGTH
IN. (mm)
DESCRIPTION
(comes with T3 fuel cell)
T4012S
1/2" (12.7 mm)T4 1/2" Plated premium steel pin
T4034S*
3/4" (19.1 mm)T4 3/4" Plated step shank concrete pin
T4100
1" (25.4 mm)T4 1" Plated concrete pin
Shank diameter = .125 *Shank diameter = .104 / .125 Head diameter = .250
Find your nearest store / distributor to purchase your Ramset T4MAG, related pins and fuel. View Ramset Gas Tools in a full screen map