- Part No.T3SS
- Length13-1/2"
- Height15"
- Weight7 lbs
- Pin Guide O.D1/2" Standard, 7/8" Magnetic
- Maximum Pin Length1-1/2"
- Fuel Cell1000 shots
- Battery (Charged)3000 shots
Ramset is serious when it comes to driving job speed by creating the T3SS—the single shot tool that will help move/contractors from powder to gas. To make the T3SS the most versatile gas tool in the industry, users can change out nosepieces to accommodate any fastening need. From metal-to-concrete, hard concrete or steel, pan deck, block and just about surface you can think of the T3SS works for you.
Click here for full product selection and performance tables for the T3SS; Click here for full catalog pages for the T3SS.
Made from AISI 1060-1065 steel. Austempered to a core hardness of 52-56 Rc
Typical tensile strength: 270,000 psi
Typical shear strength: 162,000 psi
Standard finish:
| FASTENER PART NUMBER | SHANK DIA. (INCH) | MINIMUM PENETRATION (INCH) | INSTALLED IN STONE AGGREGATE CONCRETE CONCRETE COMPRESSIVE STRENGTH ALLOWABLE LOAD – Ultimate Load | HOLLOW BLOCK Grade N, Type 1 |
||||||
| 4000 PSI | 6000 PSI | 3000 PSI Lightweight LOWER FLUTE | FACE SHELL Min 1-1/4" face thickness |
|||||||
| TENSION (LBS) | SHEAR (LBS) | TENSION (LBS) | SHEAR (LBS) | TENSION (LBS) | SHEAR (LBS) | TENSION (LBS) | SHEAR (LBS) | |||
| MP034TH* | 0.125 | 5/8 | 78 | 426 | 80 | 574 | 62 | 308 | ---- | ---- | 72 | 361 | 242 | 1210 | 133 | 691 | ---- | ---- |
| 3/4 | 104 | 593 | 195 | 977 | 132 | 658 | 206 | 1057 | 93 | 470 | 288 | 1442 | 84 | 444 | 87 | 446 | ||
| 34CLIP | 0.104/ .125 | 5/8 | 62 | 310 | ---- | ---- | 106 | 528 | ---- | ---- | 44 | 220 | ---- | ---- | ---- | ---- | ---- | ---- |
| 38HSMP034,12HSMP034, 34HSMP034,TSHMP034 | 0.104/ .125 | 5/8 | 60 | 357 | 117 | 587 | 107 | 533 | 191 | 957 | 54 | 269 | 230 | 1150 | 71 | 357 | 123 | 613 |
* ESR-1955 pin data applies. Note 1: ALLOWABLE loads are shown in the LARGE BOLD font, Ultimate loads are shown in smaller italic font. Note 2: Testing conducted in accordance with ICC AC70 & ASTM E1190. Note 3: Safety factors are based on coefficient of variation. In accordance with ICC AC70, the safety factor will be no less than 5. Note 4: Values shown in concrete are for fastener only. Connected members must be investigated separately. Note 5: Cyclic, fatigue, shock loads and other design criteria may require a different safety factor. Note 6: Job-site testing may be required to determine actual job site values. Note 7: Minimum edge distance is 3 inches unless otherwise approved. In hollow block applications, no more than one fastener per cell. Note 8: For SI: 1 lbf = 4.448 N, 1 inch = 25.4 mm, 1 ksi = 6.89MPa.
Click here for List of Authorized Ramset Service Centres
Ramset warrants that new T3SS systems power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below.
TWO-YEAR/50,000 SHOT WARRANTY
A two-year/50,000 shot warranty, which ever comes first, will apply to all parts,
except those listed below as normal wearing parts, or parts which are specifically covered by an extended warranty.
SIX-MONTH/10,000 SHOT WARRANTY
A six-month/10,000 shot warranty applies to the following parts, which are considered normal wearing parts:
• Bumper
• Piston Assembly
• Metal Seal Rings
• Piston Rings
The warranty period is based off of tool build date, determined from the tool serial number. Ramset may extend the warranty time frame from the date of purchase with a qualifying document proving date of purchase.
For full warranty statement, click here.
Part No. T3FUEL
Fuel Cell–T3SS
Qty: 12 (6–2 packs)
Part No. B0092
Battery–T3SS
Qty: 1
Part No. M150200
Magnetic Nose Piece
Qty: 1
Part No. B0022
Battery Charger–T3SS
Qty: 1
| One Hole Strap | Used to attach conduit or armored cable to concrete. Fastener pre-assembled to a 16 gauge conduit strap. | |||
| PART NUMBER | SHANK DIAMETER | HEAD DIAMETER | DESCRIPTION | QTY |
| 38HSMP034 | .104/.125 | 0.3 | 3/8" Hole strap with 3/4" plated pin | 200/jar |
| 12HSMP034 | .104/.125 | 0.3 | 1/2" Hole strap with 3/4" plated pin | 100/jar |
| 34HSMP034 | .104/.125 | 0.3 | 3/4" Hole strap with 3/4" plated pin | 25/jar |
| Ceiling Clip Assembly | Pre-assembled Ceiling Clip. Plated 14 gauge clip. | |||
| PART NUMBER | SHANK DIAMETER | HEAD DIAMETER | DESCRIPTION | QTY |
| 34CLIP | .104/.125 | 0.3 | 3/4" Ceiling Clip Assembly | 100/jar |
| Tie Strap Holder | Used to install temporary lighting and secure low voltage cable to concrete, uses a standard cable tie up to 3/8" in width. Fastener pre-assembled to an 22 gage tie strap holder. | |||
| PART NUMBER | SHANK DIAMETER | HEAD DIAMETER | DESCRIPTION | QTY |
| TSHMP034 | .104/.125 | 0.3 | Tie strap holder with 3/4" plated pin | 50/jar |
| Top Hat Pin | Used for general purpose fastening to concrete. Plated pin with top hat. | |||
| PART NUMBER | SHANK DIAMETER | HEAD DIAMETER | DESCRIPTION | QTY |
| MP034TH | 0.125 | 0.3 | 3/4" Plated pin with top hap | 200/jar |
