- Part #T3MAG
- Length18-1/2"
- Height15"
- Weight9.2 lbs.
- Pin Guide O.D.590
- Fuel Cell1000 shots
- Battery (Charged)3000 shots
The newly designed nosepiece, point collation, and patented pin-feed mechanism allows for easy fastening without jamming. The T3 is ergonomically balanced for less operator fatigue. No more fumbling to get the tool into position with the “grip it & flip it” design.
Ergonomics
Versatility and Speed
Click here for full product selection and performance tables for the T3MAG; Click here for full catalog pages for the T3MAG.
GAS FASTENERS IN STEEL
(INCH) | SHANK | ALLOWABLE LOAD – |
||||||
Note 1: ALLOWABLE loads are shown in the LARGE BOLD font, Ultimate loads are shown in smaller italic font. Note 2: Testing conducted in accordance with ICC AC70 & ASTM E1190. Note 3: Safety factors are based on coefficient of variation. In accordance with ICC AC70, the safety factor will be no less than 5. Note 4: Cyclic, fatigue, shock loads and other design criteria may require a different safety factor. Note 5: Job site testing may be required to determine actual job site values. Note 6: Values shown are for fastenings that have the entire pointed end of the fastener driven through the steel plate; except as noted below. Note 7: Fastener penetration is .31″ minimum. Note 8: Fastener penetration is .29″ minimum. Note 9: Fastener penetration is .27″ minimum. Note 10: Fastener penetration is .25″ minimum. Note 11: For SI: 1 lbf = 4.448 N, 1 inch = 25.4 mm, 1 ksi = 6.89MPa
COLLATED GAS FASTENERS IN CONCRETE
NUMBER SERIES | DIAMETER (INCH) | PENETRATION (INCH) | ||||||
Straight Shank | ||||||||
NUMBER SERIES | DIAMETER (INCH) | PENETRATION (INCH) | ||||||
LIGHT WEIGHT CONCRETE | LIGHT WEIGHT CONCRETE WITH METAL DECK | UNITS (CMU) ANY LOCATION |
||||||
TENSION (LBS) | SHEAR (LBS) | TENSION (LBS) | SHEAR (LBS) | TENSION (LBS) | SHEAR (LBS) |
|||
Straight Shank | ||||||||
Note 1: ALLOWABLE loads are shown in the LARGE BOLD font, Ultimate loads are shown in smaller italic font. Note 2: Testing conducted in accordance with ICC AC70 & ASTM E1190. Note 3: Safety factors are based on coefficient of variation. In accordance with ICC AC70, the safety factor will be no less than 5. Note 4: Values shown in concrete are for the fastener only. Connected members must be investigated separately. Note 5: Cyclic, fatigue, shock loads, and other design criteria may require a different safety factor. Note 6: Job site testing may be required to determine actual job site values. Note 7: Minimum edge distance in concrete is 3 inches unless otherwise approved. Note 8: For SI: 1 lbf = 4.448 N, 1 inch = 25.4 mm, 1 ksi = 6.89MPa. Note 9: T3 straight shank allowable tension value in face shell of hollow CMU is 133 lbs.
Click here for List of Authorized Ramset Service Centres
Ramset warrants that new T3MAG systems power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below.
TWO-YEAR/50,000 SHOT WARRANTY
A two-year/50,000 shot warranty, which ever comes first, will apply to all parts,
except those listed below as normal wearing parts, or parts which are specifically covered by an extended warranty.
SIX-MONTH/10,000 SHOT WARRANTY
A six-month/10,000 shot warranty applies to the following parts, which are considered normal wearing parts:
• Bumper
• Piston Assembly
• Metal Seal Rings
• Piston Rings
The warranty period is based off of tool build date, determined from the tool serial number. Ramset may extend the warranty time frame from the date of purchase with a qualifying document proving date of purchase.
For full warranty statement, click here.
Part No. T3FUEL
Fuel Cell–T3SS
Qty: 12 (6–2 packs)
Part No. B0092
Battery–T3SS
Qty: 1
Part No. B0022
Battery Charger–T3SS
Qty: 1
Part No. 906001 (T3MAG v2) / Part No. B0237 (T3MAG)
Magnetic Disc Probe
Qty: 1
| T3MAG Fuel/Pin Pack | ||
IN. (mm) | (comes with T3 fuel cell) |
|
| 1/2" (12.7 mm) | 1/2" Plated premium steel pin | |
| 3/4" (19.1 mm) | 3/4" Black concrete pin | |
| 3/4" (19.1 mm) | 3/4" Plated step shank pin | |
| 1" (25.4 mm) | 1" Plated concrete pin= | |
| Shank diameter = .125 *Shank diameter = .104 / .125 Head diameter = .250 | ||
